Shakers - OS / SKC Models

1) Microprocessor PID controller enables reproducible results.

2) User friendly control panel with durable membrane touch switch and control knob.

3) Automatic run after power interruption.

4) Built-in RS-232 port and USB port for external control and data collection. (except for SKC)

5) Audible/Visible alarm activated by shaking speed deviation. (except for SKC)

6) Worry-free operation is guaranteed by automatic shaking speed adjustment in case of excessive workload.

7) Wide speed range even with heavy workload.

8) Repetitive task can be easily performed as the platform stops where it starts.

9) Smooth start and smooth stop function prevents chemical spills from flasks or test tubes.

Shakers - CMS / CPS / CRS / CWS Models

1) Microprocessor PID control.

2) Digital speed control providing gentle shaking motion.

3) Smooth, quiet, uniform, and yet powerful shaking motion.

4) Easy to adjust tilt angle. (only for CRS, CWS)

5) One-touch timer for time-dependent shaking operations. (1 min to 99 hour 59 min.)

6) Compact and lightweight design allowing for use inside chambers.

7) Digital VFD display for speed and shaking motion.

8) Its polypropylene main body is highly chemical-resistant and easy-to-clean.

9) Low-profile design with rubber feet for minimal vibration and noise.

Heating Shaker

1) Microprocessor PID control ensuring consistent shaking motion and precision accuracy.

2) Simple temperature calibration.

3) Memory function of programmed protocols allowing relevant parameters (such as temp., rpm, time) of each protocol step to be stored.

4) Bright VFD display with responsive touch buttons.

5) Its polypropylene main body is highly chemical-resistant and easy-to-clean.

6) Optimal heat transfer is achieved by the tight coupling design of the main body and the corrosion-resistant anodized aluminum blocks.

Incubated Shakers

1) Intuitive touch LCD controller with easy icons and logical menus.

2) Automatic run after power interruption.

3) Built-in RS-232 port and USB port for external control and data collection.

4) Audible/Visible alarm activated by shaking speed deviation.

5) Worry-free operation is guaranteed by automatic shaking speed adjustment in case of excessive workload.

6) Microprocessor PID control and autotuning.

7) Three point temperature calibration.

8) Wide speed range even with heavy workload.

9) Repetitive task can be easily performed as the platform stops where it starts.

10) Smooth start and smooth stop function prevents chemical spills from flasks or test tubes.

Rotator - CRS Model

1) Adjustable speed range from 2 to 70 rpm.

2) Fully adjustable tilt angle up to 90°.

3) Digital speed control providing gentle rotating even at low speed.

4) Simple fixture of accessories equipped to disk for quick installation and removal.

5) Available to rotary maximum 108 test tubes

6) Vivid and colorful vacuum fluorescent display (VFD) with touch-sensitive keypad.

7) One-touch timer range: 1 min. to 99 hr. 59 min.

8) Compact and lightweight design allow for use in cold rooms or incubators.

9) Stepping motor with self-protection function for advanced durability.

10) Its polypropylene main body is highly chemical-resistant and easy-to-clean.

Funnel Shaker - RS-2 Model

1) Vertical reciprocation at a maximum of 300 rpm and 40 mm stroke length.

2) Tilt angle adjustment from 0 to 20° for maximum mixing efficiency.

3) One-touch mechanism for convenient funnel installation and removal.

4) Fits cone or cylindrical type funnels of up to 2L capacity (capacity limit for previous model was 1L).

5) Controller with display panel installed at a 20º angle, allowing good visibility even from the floor; ease of operation.

6) Safety devices for protecting the user and the experiment (protecting the device from overcurrent, automatic resumption upon return of power supply after power failure).